The LimbO protector is a comfortable, easy-to-use, reusable waterproof protector which can be completely submerged. It is a self-sealing, self-supporting garment that prevents water penetration to plaster casts and wound bandages on arms or legs during bathing. It is simple and comfortable to use and will last through the average user's duration of treatment.

The LimbO provides a significant quality of life improvement for the user. It is a non-sterile product and is primarily intended for use in a bath or shower. The LimbO gives you the healing benefits that water can provide whilst ensure the plaster cast or bandage remains dry.

Waterproof protection for your PICC line, midline, or dressing on the elbow or upper arm
Perfect for your shower (not suitable for the bath – please select full arm protector instead)
Easy to put on and use
Comfortable, soft neoprene seals

Sizing Information:

Measure the circumference above the PICC line, midline, or dressing (directly on the skin).

Model M65 Adult Regular - 5060032041247

This LimbO is suitable for 25 to 29 cm skin circumference and is 26 cm in length.

Model M75 Adult Large - 5060032041834

This LimbO is suitable for 30 to 39 cm skin circumference and is 26 cm in length.

Using Your LimbO

How to put on your LimbO Product

Putting your injured limb inside the LimbO

Step 1
Using your thumb and forefinger, carefully grip your LimbO’s black neoprene seal by its outer edge, where it joins the clear plastic body of the protector. Insert your injured limb into the seal opening, gently pushing it into the protector. (For leg models, fit the LimbO so that your toes are at the pointed end). Be careful not to puncture the LimbO with sharp fingernails or jewelry.

Step 2
Still gripping the LimbO as described above, draw it up, easing the black seal over the cast or bandage, then allow the seal to turn inwards as it slides up to secure.

Securing the LimbO

Step 3
When up as high as possible, pull the LimbO down slightly so that the seal reverses itself, turning upwards so that the inner surface of the seal is in direct contact with your skin.

Step 4
Ensure that the seal of your LimbO lays flat against your skin and is wrinkle-free with a snug, comfortable fit to guarantee waterproof protection.

Step 5
To avoid excessive ' ballooning ' and floating, it is advisable to remove some of the air trapped in the LimbO, particularly if used in a bath. This is done by carefully lifting the seal out of the water and squeezing the air out of the LimbO.

Taking off your LimbO Waterproof Protector

Step 1
Carefully roll the seal back on itself a little and ease it over your cast or dressing. You will now be able to slide the protector off your limb easily.

Step 2
Hang your LimbO upside down away from any direct heat source to dry. It will be ready to use whenever needed, assisting your recovery.

Care & Use Guidelines
Cleansing & Storage

Use a mild disinfectant or detergent to hand-wash the LimbO as required.
Dry your LimbO thoroughly away from direct heat before storing.
Avoid folding the neoprene seal and check it remains undamaged before re-using.
Store in a dry place at room temperature.

User Guidelines

To avoid damaging leg models when using a LimbO over roughcast, you must fit a thick sock or soft cloth over the lower part of the cast, i.e., between the cast and the LimbO, to provide some cushioning for the LimbO.
To protect the foot area from being pierced, avoid walking on hard floors. If possible, put on your LimbO in the bathroom and step directly into your bath or shower.
The LimbO should be worn for a maximum of 20 minutes to avoid trapped warm air causing perspiration and, therefore, the risk of a damp cast or dressing.
Please take extra care not to slip or trip when entering and exiting the bath or shower. Your LimbO will provide secure protection and is made from a non-slip material, enabling you to resume normal bathing.

Technical Information

Seal Material

Closed-cell neoprene with bonded nylon fabric outer layer for additional strength.
Latex-free.

Garment Sheet Material

Three-layer calendered PVC/Nylon/PVC, flame-resistant grade.
Latex-free.

Colors

Black seal/opaque garment body.

Internal Reinforcement Material

Nylon thread mesh.

Construction

All seams are welded, i.e., without adhesives.

Quality

Manufactured according to ISO 9001 standards, the product is CE marked as a Class 1 Medical Device.